|
|
|
642 990 29 07-FEBI KIT
2007 & LATER 3.0L V6 Diesel SPRINTER Fuel Injector Bolt Kit
Complete set of six stretch bolts and six lower injector seals.
Any time an injector is replaced, both the bolt and the seal must be replaced.
These two components should never be reused.
|
|
|
|
|
642 070 12 87
Diesel Fuel Injector - New 3.0 V6 2010 & LATER
Original New Factory Injector - For BlueTec OM642.896, OM642.898 & OM642.899 V6 diesel engines 2010 & Later
Only for BluTec engines 2010 and later - Six Required, Sold Individually
|
|
|
|
|
642 070 13 01
Diesel Injection Pump REMAN/EXCHANGE 3.0L V6 Diesel 2010 & LATEROM 642.993 V6 diesel engine 2010 and Later
NOT for BlueTec engines 2007-2009
This is a remanufactured Mercedes Benz pump. It will be furnished in
either a Mercedes Benz or a Bosch box. In either case, these pumps are
remanufactured by Bosch, the original supplier to Mercedes Benz.
All returned cores must be complete, undamaged and fully assembled or they will not be accepted for refund. |
|
|
|
|
DPF KIT
DPF Cleaning Kit 2007 & LaterComplete kit with all necessary items for cleaning the DPF (Diesel Particulate Filter)
Incudes:
1 x Pressurized Spray Gun
1 x Spray wand with five nozzle attachments
1 x DPF Filter Cleaner (also available separately)
1 x DPF Filter Purge (also available separately)
|
|
|
|
|
007 153 43 28
Exhaust Back Pressure Sensor/Low Fuel Pressure Sensor 2002-2003 & 2007 & LATER 3.0L V6Located adjacent to EGR cooler on the 3.0L V6 models
Located on
left side of engine block on 2002-2003 5 CYL models (known as a low fuel pressure sensor)
Female plug, three contact pins inside plug housing.
|
|
|
|
|
000 905 52 05
Exhaust Temperature Sensor #2 2007 & LATERLocated at inlet of DPF (Diesel Particulate Filter)
|
|
|
|
|
009 542 55 18
Front Oygen Sensor-2019+ Sprinter 2.0L 4 CYL & METRIS 2016+Front Oxygen sensor, located before the catalyst
|
|
|
|
|
005 153 23 28
Fuel & Oil Temperature Sender 2002 & LATER2 contact pins, straight electrical connector.
Located on the injection pump on front of engine block on the 2.7L 5 CYL diesel engines.
Located near oil pan for the 3.0L V6 diesel engines.
|
|
|
|
|
21013
Fuel Injection Hose Clamp 13 mm 2002 & LATER
Clamping Range 12.5 - 14mm
These are special fuel hose clamps with rolled edges and no open serrations so the clamp will not cut into the hose.
If you are replacing all of the original Mercedes factory "Clic" style clamps on a ......
2002-2003 Sprinter...................... Order 4 x 13mm clamps
2004-2006 Sprinter...................... Order 9 x 13mm clamps & 1 x 15mm clamp
2007-2009 Sprinter...................... Order 6 x 13mm clamps & 6 x 15mm clamps
|
|
|
|
|
21015
Fuel Injection Hose Clamp 15mm 2002 & LATERClamping Range 13.5 - 15.5mm
These are special fuel hose clamps with rolled edges and no open serrations so the clamp will not cut into the hose.
If you are replacing all of the original Mercedes factory "Clic" style clamps on a ......
2002-2003 Sprinter........... Order 4 x 13mm clamps
2004-2006 Sprinter........... Order 9 x 13mm clamps & 1 x 15mm clamp
2007-2009 Sprinter........... Order 6 x 13mm clamps & 6 x 15mm clamps
|
|
|
|
|
21017
Fuel Injection Hose Clamp 17mm 2002 & LATERClamping Range 16-18 mm
These are special fuel hose clamps with rolled edges and no open serrations so, the clamp will not cut into the hose
If you are replacing replacing all of the original Mercedes factory "Clic" style clamps on a ......
2002-2003 Sprinter........................order 4 x 13mm clamps
2004-2006 Sprinter........................order 9 x 13mm clamps & 1 x 15mm clamp
2007-2009 Sprinter........................order 6 x 13mm clamps & 6 x 15mm clamps
|
|
|
|
|
642 016 00 38
Fuel Injector Retainer 2007 & LATER 3.0L V6All 2007 and later 3.0L V6 Diesel engines
|
|
|
|
|
000 990 29 07-FEBI
Fuel Injector Retainer Bolt 2002 & LATER 2.7L & 3.0L
These are manufactured by Febi-Bilstein, the OEM supplier to Mercedes.
T-40 Torx head screw, 55mm stretch bolt.
Order 1 screw for each injector.
These bolts are to be tightened in two stages. Torque to 7 Nm (62 inch lbs), then an additional 90 degrees.
|
|
|
|
|
642 070 08 00
Fuel Injector Supply Line 3.0L V6 2007 & LATERSteel line from the either fuel rail to each of the six injectors
These lines will often leak at either end, especially if they have been over-torqued.
Six required. one for each injector.
|
|
|
|
|
642 070 12 87 80
Fuel Injector-REMAN/EXCHANGE 3.0L V6 2010 & LATER
Original remanfactured/exchange factory Bosch injector
For BlueTec OM 642.896, OM642.898 & 642.899 V6 diesel engine
A CORE DEPOSIT OF $120 PER INJECTOR WILL BE ADDED TO YOUR INVOICE.
THIS DEPOSIT WILL BE REFUNDED UPON RETURN OF YOUR OLD REBUILDABLE INJECTOR.
All returned cores must be complete, undamaged and fully assembled or they will not be accepted for refund.
Only for BluTec engines 2010 and later
THESE ARE ALSO AVAILABLE NEW, SEE BELOW
|
|
|
|
|
006 153 78 28
Fuel Pressure Sensor 2010 & LATER
Oval shaped Plug, no flat edges- if you have a 2009 or 2010 check the plug connector first Located on back end of the right side fuel rail
The 90 degree sensor on the left fuel rail is not available as a separate component and is only available with the left fuel rail assembly.
|
|
|
|
|
021 997 97 45
Fuel Pump Seal RingHigh Pressure Mechanical Fuel Pump Seal |
|
|
|
|
642 070 09 00
Fuel Rail Connecting Line L to R 2007 & LATERSteel line from the left fuel rail to the right fuel rail.
This line will often leak at either end, especially if it has been over-torqued.
One required
|
|
|
|
|
642 070 10 00
Fuel Rail Supply Line 2010 & LATER 3.0L V6aka Fuel Delivery Line
Steel line from the high pressure injection pump to the fuel rail.
This line will often leak at either end, especially if it has been over-torqued.
One required
|
|
|
|
|
000 078 05 80
Fuel Return Line Seal V6 & 2.1 DIESEL
1 required for each injector.
Replace these seals at the same time that you replace the fuel return line or you may have leakage.
Seals leak line (fuel return line) to each injector.
These are made by Bosch and are the identical seal ring sold at a Mercedes franchise dealer.
|
|
|
|
|
642 990 29 07-MB KIT
Genuine Mercedes - 2007 & LATER 3.0L V6 Diesel SPRINTER Fuel Injector Bolt Kit
Complete set of six stretch bolts and six lower injector seals.
Any time an injector is replaced, both the bolt and the seal must be replaced.
These two components should never be reused.
|
|
|
|
|
000 990 29 07-MB
Genuine Mercedes - Fuel Injector Retainer Bolt 2002 & LATER 2.7L & 3.0L
These are Genuine Mercedes bolts.
T-40 Torx head screw, 55mm stretch bolt.
Order 1 screw for each injector.
These bolts are to be tightened in two stages. Torque to 7 Nm (62inlbs) |
|
|
|
|
177 072 00 00
Injector Seal Kit 2.0L Sprinter 2019+ & Metris
One kit per injector
4 required
|
|
|
|
|
642 070 27 95
Left Fuel Distribution Rail 2010 & LATER 3.0L V6Driver's side rail. Includes Fuel Control Valve on end of rail.
The fuel control valve (642 070 02 46) with the 90 degree connection is only available with the fuel rail.
|
|
|
|
|
611 017 00 60
Lower Fuel Injector Seal Ring 2002 & LATER
Lower copper seal at tip of injector. One required for each injector nozzle.
|
|
|
|
|
006 542 49 18
Oxygen Sensor 3.0 V6 2010 & LATER & 2014-2016 2.1L 4 CYLFits all 3.0 liter Diesel Engines from 2010 and later and the 2014-2016 4 CYL engines (BlueTec)
|
|
|
|
|
642 070 30 95
Right Fuel Distribution Rail 2010 & LATER 3.0L V6Right side or Passenger's side
|
|
|