|
|
|
2007-2018 Sprinter 2500 BILSTEIN Strut/Shock Absorber Kit ***FREE USA SHIPPING***Set of all four shock absorbers, made by Bilstein in Germany.
Only for 2500 Cargo Van.
Not for Winnebago or Itasca motor homes, which are built on the 3500 chassis.
Not for passenger vans.
2 to 3 Day Shipping to any US Zip Code included!
|
|
|
|
|
2007-2018 Sprinter 3500 BILSTEIN Strut/Shock Absorber Kit ***FREE USA SHIPPING***Set of all four shock absorbers, made by Bilstein in Germany.
Only for 3500 Cargo Van.
Not for Winnebago or Itasca motor homes, which are built on the 3500 chassis.
Not for passenger vans.
2 to 3 Day Shipping to any US Zip Code included!
|
|
|
|
|
Front BILSTEIN Strut Assembly-2500 STANDARD DUTY 2007-2018
Fits all Sprinter 2500 models, left or right.
Supersedes old part 22-184238
MFG: Bilstein
These are the standard duty B4 struts (black in color).
|
|
|
|
|
Front BILSTEIN Strut Assembly-2500/3500 B6 HEAVY DUTY 2007-2018
Fits all Sprinter II 2500 and 3500 models, left or right.
These struts supersede previous Bilstein strut 22-249326, which has been discontiued
MFG: Bilstein B6 4600 HD unit
Will not fit 4WD models, as they are far too short in length.
Sold individually. Order two if doing both sides of vehicle.
These are the heavy duty B6 struts (yellow in color).
|
|
|
|
|
Front BILSTEIN Strut Assembly-2500/3500 2007-2018Fits all Sprinter 3500 models
Also recommended for the 2500 as a heavier duty alternative, e.g. motorhome/camper and heavier cargo loads.
MFG: Bilstein |
|
|
|
|
Front Strut Assembly 2500/3500 KYB 2007-2018Fits all Sprinter 2500 & 3500 models
MFG: KYB
|
|
|
|
|
Front Strut Assembly-2500 KONI 2007-2018
Sold individually, order two if doing both sides of van.
Fits all Sprinter 2500 models
MFG: Koni |
|
|
|
|
Front Strut Assembly-3500 KONI 2007-2018Sold individually, order two if doing both sides of van.
Fits all Sprinter 3500 models
MFG: Koni |
|
|
|
|
Front Strut Boot 2007-2018Front strut dust boot for all 2500 and 3500 models, including 4WD models
Sold individually....order two if doing both sides
|
|
|
|
|
Front Strut Mount 2007 & LATER2 required per vehicle, sold each. Fits all models 1500, 2500, 3500 including 4WD models
|
|
|
|
|
Front Transverse Leaf Spring 2007-2018Often found to be the cause of front end "bottoming out" problems. This composite spring sags or breaks in higher mileage vehicles, causing the van's front end to droop and a lot of suspension banging noises.
|
|
|
|
|
Front Transverse Leaf Spring End Bushing 2007-2018
Two are required. One for each end of the leaf spring
|
|
|
|
|
Front Transverse Leaf Spring Lower Seat 2007-2018
Two are required. Situated below the leaf spring.
|
|
|
|
|
Front Transverse Leaf Spring Upper Seat 2007-2018
Two are required. Situated on the top of the leaf spring.
|
|
|
|
|
Rear BILSTEIN Shock Absorber-2500 CAMPER VAN 2007-2018
Only for rear of 2500 Sprinter camper suspension.
Not for Winnebago or Itasca motor homes on 3500 chassis.
|
|
|
|
|
Rear BILSTEIN Shock Absorber-2500 CARGO VAN 2007-2018Only for rear of 2500 cargo van.
Not for Winnebago or Itasca motor homes, built on the 3500 chassis.
Not for passenger vans.
|
|
|
|
|
Rear BILSTEIN Shock Absorber-2500 MOTORHOME 2002-2018
TWO REQUIRED, SOLD INDIVIDUALLY
Heavy duty (High Pressure Gas) for most Sprinter based motor home with single wheel rear axle, e.g. Airstream Westfalia
OVERALL LENGTH OF THIS SHOCK ABSORBER IS APPROXIMATELY 560 mm or 22 inches with both end bushings having 14mm holes. Some people report requiring a adpter sleeve to make these fit the original 12mm mounting bolt on the bottom end.
|
|
|
|
|
Rear BILSTEIN Shock Absorber-3500 CARGO VAN 2007-2018
Only for rear of 3500 Sprinter cargo van.
Not for Winnebago or Itasca motor homes. |
|
|
|
|
Rear BILSTEIN Shock Absorber-3500 MOTORHOME 2002-2018
TWO REQUIRED, SOLD INDIVIDUALLY
Heavy duty (High Pressure Gas) for most Sprinter based motor home with dual wheel rear axle. e.g. Winnebago View, Itasca Navion
OVERALL LENGTH OF THIS SHOCK ABSORBER IS APPROXIMATELY 593 mm or 23.25 inches with both end bushings having 14mm holes. Some people report requiring a adpter sleeve to make these fit the original 12mm mounting bolt on the bottom end.
|
|
|
|
|
Rear Shock Absorber 4WD Sprinter ONLY 2015-2018Fits left or right rear for 4WD models only
|
|
|
|
|
Rear Shock Absorber-2500 KONI 2007-2018Sold individually, order two if doing both sides of van.
Fits all Sprinter 2500 models
MFG: Koni |
|
|
|
|
Rear Shock Absorber-2500 KYB 2007-2018Only for rear of 2500 cargo van RWD
Not for Winnebago or Itasca motor homes, built on the 3500 chassis.
Not for passenger vans, nor 4WD models
|
|
|
|
|
Rear Shock Absorber-2500 Passenger Van 2007-2018Only for rear of 2500 passenger van. These are the same Sachs shocks sold at a franchise Dodge, Freightliner or Mercedes dealer.
Not for Winnebago or Itasca motor homes, built on the 3500 chassis.
Not for cargo vans.
|
|
|
|
|
Rear Shock Absorber-2500 SACHS 2007-2018
Only for rear of 2500 CARGO VAN
Not for Winnebago or Itasca motor homes, built on the 3500 chassis.
Not for passenger vans.
|
|
|
|
|
Rear Shock Absorber-3500 OEM 2007-2018
|
|
|
|
|
Rear Shock Absorber-3500 KYB 2007-2018Standard rear shock absorber made by KYB
|
|
|
|
|
Rear Wheel Bearing & Hub Assembly 2500 2007-2018 *FREE USA SHIPPING*Fits left or right side - 2500 models ONLY
This is the entire, complete assembly, which includes the wheel hub.
This is an OEM part, made by Febi-Bilstein, an original supplier to Mercedes.
|
|
|
|
|
Upper & Lower Strut Stop Kit 2007-2018Set of both upper and lower strut stops. 2 sets required per vehicle.
Order two kits if doing both sides of vehicle
|
|
|