|
|
|
642 990 29 07KIT
2007 & LATER 3.0L V6 Diesel SPRINTER Fuel Injector Bolt KitComplete set of six stretch bolts and six lower injector seals.
Any time an injector is replaced, both the bolt and the seal must be replaced.
These two components should never be reused.
|
|
|
|
|
642 078 00 01
2007-2009 Sprinter 3.0 V6 Diesel Fuel Hose Kit ***FREE USA SHIPPING***REQUIRES SIX 13MM AND SIX 15MM HOSE CLAMPS, SHOWN BELOW.
All the six small fuel hoses in and around the engine compartment, labeled A thru F on our site. All are Genuine Mercedes parts.
The fuel return hose assembly (H) and drain/purge line (G) are NOT included. You can see these two hoses below, along with the special hose clamps for fuel hoses.
|
|
|
|
|
642 070 12 87
Diesel Fuel Injector - New 3.0 V6 2010 & LATER
Original New Factory Injector - For BlueTec OM642.896, OM642.898 & OM642.899 V6 diesel engines 2010 & Later
Only for BluTec engines 2010 and later - Six Required, Sold Individually
|
|
|
|
|
642 070 03 01
Diesel Injection Pump REMAN/EXCHANGE 3.0L V6 Diesel 2007-2009OM 642.993 V6 diesel engine 2007-2009 models
NOT for BlueTec engines 2010 and later
This is a remanufactured Mercedes Benz pump. It will be furnished in
either a Mercedes Benz or a Bosch box. In either case, these pumps are
remanufactured by Bosch, the original supplier to Mercedes Benz.
All returned cores must be complete, undamaged and fully assembled or they will not be accepted for refund.
|
|
|
|
|
642 070 13 01
Diesel Injection Pump REMAN/EXCHANGE 3.0L V6 Diesel 2010 & LATEROM 642.993 V6 diesel engine 2010 and Later
NOT for BlueTec engines 2007-2009
This is a remanufactured Mercedes Benz pump. It will be furnished in
either a Mercedes Benz or a Bosch box. In either case, these pumps are
remanufactured by Bosch, the original supplier to Mercedes Benz.
All returned cores must be complete, undamaged and fully assembled or they will not be accepted for refund. |
|
|
|
|
000 905 52 05
Exhaust Temperature Sensor #2 2007 & LATERLocated at inlet of DPF (Diesel Particulate Filter)
|
|
|
|
|
651 070 15 95
Fuel Distribution Rail Assembly 2014-2016 2.1L 4 CYL
Fuel rail which connects to all four injectors. Both of the sensors, at each end of the rail, are included. Neither of these two sensors are available
individually. They are only sold as part of the entire fuel rail assembly.
Brand new, complete and original Bosch fuel rail. This is the exact same rail sold at a franchise Mercedes dealer at one third of their price.
|
|
|
|
|
642 070 12 38
Fuel Filter Purge Hose (3 Pin Moisture Sensor) 3.0L V6 2010-2012
This hose connects to the moisture sensor on top of fuel filter and is the only one furnished with a metal bracket. Bleed screw is at the opposite end.
NOTE: This hose is used on those models which have the type of fuel filter with the removable 3-pin moisture sensor from 2010 to 2012
DO NOT ORDER THIS IF YOU HAVE A FUEL FILTER WITH THE NON-REMOVABLE 5-PIN MOISTURE SENSOR.
See the other version of this hose below
|
|
|
|
|
642 070 24 38
Fuel Filter Purge Hose (5 Pin Moisture Sensor) 3.0L V6 2010-2018
Hose to top of fuel filter. Snaps onto the small nipple at the top on the side. This hose has a bleed screw on the end for purging accumulated water at the bottom of the fuel filter.
NOTE: This hose is only used in conjunction with the new BlueTec engine fuel filters with the non-removable 5-pin moisture sensor.
See the other version of this hose below.
|
|
|
|
|
642 070 00 38
Fuel Filter Purge Hose 3.0L V6 2007-2009
This hose connects to the moisture sensor.on top of fuel filter. Bleed screw is at the opposite end.
DO NOT ORDER THIS HOSE IF YOU HAVE A 2010 OR LATER MODEL WITH A BLUETEC ENGINE.
THERE ARE TWO DIFFERENT FUEL FILTER PURGE HOSES FOR 2010 AND BOTH ARE SHOWN BELOW
|
|
|
|
|
651 074 00 84
Fuel Flow Control Valve 2014-2016 2.1L 4 CYLThis is the larger flanged valve piece, located on the injection pump held in place by two screws.
|
|
|
|
|
642 070 57 81
Fuel Hose A 3.0L V6 2010 & LATER
REQUIRES TWO 13MM CLAMPS.
Fuel filter to high pressure injection pump
|
|
|
|
|
642 070 05 81
Fuel Hose B 3.0 V6 2007-2009Hose from output side of fuel filter to high pressure injection pump
Hose uses 13mm clamps
|
|
|
|
|
642 070 36 81
Fuel Hose B 3.0L V6 2010 & LATER
Only for 3.0L V6 Diesel
REQUIRES TWO 13MM CLAMPS. |
|
|
|
|
642 078 19 81
Fuel Hose C 3.0L V6 2007-2009One of two hoses that connect the fuel pipe sections together
Hose use 15 mm clamps
|
|
|
|
|
642 078 45 81
Fuel Hose C 3.0L V6 2010 & LATER
Only for 3.0L V6 Diesel
Fuel filter to separator
REQUIRES TWO 15MM CLAMPS.
|
|
|
|
|
642 078 13 81
Fuel Hose D 3.0L V6 2010 & LATER
Only for 3.0L V6 Diesel BlueTec
REQUIRES TWO 15MM CLAMPS.
|
|
|
|
|
642 078 21 81
Fuel Hose D 3.0L V6 2007-2009Short, straight 50mm (2 inch) section
13mm clamp on each end
|
|
|
|
|
642 078 32 81
Fuel Hose E 3.0L V6 2010 & LATER
Only for 3.0L V6 Diesel BlueTec
REQUIRES TWO 15MM CLAMPS.
PART # ON HOSE IS 642 078 32 81
|
|
|
|
|
642 078 23 81
Fuel Hose E 3.0L V6 2007-2009Feed hose from metal pipe to input side of fuel filter
Hose uses 2 x 15 mm clamps
|
|
|
|
|
642 078 25 81
Fuel Hose F 3.0L V6 2007-2009Hose uses 2 x 15 mm clamps
|
|
|
|
|
651 070 28 01
Fuel Injection Pump 2014-2016 2.1L 4 CYLHigh pressure injection pump located at front of engine
|
|
|
|
|
642 016 00 38
Fuel Injector Retainer 2007 & LATER 3.0L V6All 2007 and later 3.0L V6 Diesel engines
|
|
|
|
|
651 016 05 38
Fuel Injector Retainer 2014-2016 4 CYL ONLY
Only for the OM651 4 CYL engines
Use with T-50 stretch bolt shown below
|
|
|
|
|
001 990 26 07
Fuel Injector Retainer Bolt 2014-2016 4 CYL ONLY
T-50 Torx head 55mm stretch bolt
Order 1 screw for each injector
Only for the OM651 4 CYL engines
|
|
|
|
|
642 070 56 32
Fuel Injector Return Line Assembly 3.0L V6 2007-2009Links all of the six injectors and returns surplus fuel to the tank. None of the fittings on this assembly are sold individually - only the seal rings, as shown below.
See seal rings below, Six Required, one for each injector to seal each of the snap on connections of this hose. It is important to replace these at the same time to avoid leakage.
|
|
|
|
|
642 070 75 32
Fuel Injector Return Line Assembly 3.0L V6 2010-2013Links all of the six injectors and returns surplus fuel to the tank.
None of the fittings on this assembly are sold individually, only the o-rings, as shown below.
See seal rings below, six required, one per each injector to seal each of the snap on connections of this hose.
|
|
|
|
|
642 070 81 32
Fuel Injector Return Line Assembly 3.0L V6 2014 & LATER
Original Bosch unit - The same as sold at a Mercedes dealer
Links all of the six injectors and returns surplus fuel to the tank. None of the fittings on this assembly are sold individually, only the o-rings, as shown below.
See seal rings below, Six required, one per each injector to seal each of the snap on connections of this hose.
|
|
|
|
|
642 070 08 00
Fuel Injector Supply Line 3.0L V6 2007 & LATERSteel line from the either fuel rail to each of the six injectors
These lines will often leak at either end, especially if they have been over-torqued.
Six required. one for each injector.
|
|
|
|
|
642 070 15 87
Fuel Injector-NEW 3.0L V6 2007-2009Need high temp anti seize grease? Click Here
Original new factory Bosch injector
For OM 642 V6 diesel engine
2007-2009 models only (Not for BluTec 2010 and later)
Six required, sold individually
THESE INJECTORS ARE BRAND NEW AND NOT REMANUFACTURED AND AS SUCH, NO CORE DEPOSIT IS REQUIRED.
REMANUFACTURED INJECTORS ARE ALSO AVAILABLE, SEE BELOW |
|
|
|
|
642 070 12 87 80
Fuel Injector-REMAN/EXCHANGE 3.0L V6 2010 & LATER
Original remanfactured/exchange factory Bosch injector
For BlueTec OM 642.896, OM642.898 & 642.899 V6 diesel engine
A CORE DEPOSIT OF $120 PER INJECTOR WILL BE ADDED TO YOUR INVOICE.
THIS DEPOSIT WILL BE REFUNDED UPON RETURN OF YOUR OLD REBUILDABLE INJECTOR.
All returned cores must be complete, undamaged and fully assembled or they will not be accepted for refund.
Only for BluTec engines 2010 and later
THESE ARE ALSO AVAILABLE NEW, SEE BELOW
|
|
|
|
|
642 070 15 87 80
Fuel Injector-REMAN/EXCHANGE 3.0L V6 2007-2009
Original Remanufactured/exchange factory Bosch injector
For OM 642 V6 diesel engine
2007-2009 models only (Not for BluTec 2010 and later)
Six required, sold individually
All returned cores must be complete, undamaged and fully assembled or they will not be accepted for refund.
THESE ARE ALSO AVAILABLE NEW, SEE BELOW
|
|
|
|
|
601 997 03 45
Fuel Line Seal Ring 2002-2003 & 2007-2009
O-ring used at both ends of the white plastic fuel lines on the OM612 5 CYL engine
Also used on 2007-2009 3.0 V6 on end of fuel purge hose where it enters the fuel filter.
Do not order these seal rings if you are ordering new hoses, as the hoses are furnished with the seals already in place.
|
|
|
|
|
006 153 78 28
Fuel Pressure Sensor 2010 & LATER
Oval shaped Plug, no flat edges- if you have a 2009 or 2010 check the plug connector first Located on back end of the right side fuel rail
The 90 degree sensor on the left fuel rail is not available as a separate component and is only available with the left fuel rail assembly.
|
|
|
|
|
906 470 29 00
Fuel Pump Tank Module-3.0L V6 DIESEL 2007-2018This pump is for all 3.0L V6 models with or without an auxiliary heater booster.
This is the same Bosch unit as sold at a franchise Dodge, Freightliner or Mercedes dealer.
This is a complete module, containing the pump, screen and the fuel tank sending unit. The tank module seal at the top of the tank is not included but is available, and shown below.
|
|
|
|
|
642 074 02 84
Fuel Quantity Control Valve 2007-2009
Located on the high pressure diesel injection pump on the front of the engine.
aka: Fuel Flow Control Valve or Solenoid
Has 90 degree plug connection
|
|
|
|
|
642 070 17 33
Fuel Rail Connecting Line L to R 2007 & LATERSteel line from the left fuel rail to the right fuel rail.
This line will often leak at either end, especially if it has been over-torqued.
One required
|
|
|
|
|
642 070 10 00
Fuel Rail Supply Line 2010 & LATER 3.0L V6aka Fuel Delivery Line
Steel line from the high pressure injection pump to the fuel rail.
This line will often leak at either end, especially if it has been over-torqued.
One required
|
|
|
|
|
642 070 07 00
Fuel Rail Supply Line 3.0L V6 2007-2009aka Fuel Delivery Line
Steel line from the high pressure injection pump to the fuel rail.
This line will often leak at either one of the ends, especially if it has been over-torqued.
One required
|
|
|
|
|
000 078 05 80
Fuel Return Line Seal V6 & 2.1 DIESEL
1 required for each injector.
Replace these seals at the same time that you replace the fuel return line or you may have leakage.
Seals leak line (fuel return line) to each injector
These are made by Bosch and are the identical seal ring sold at a Mercedes franchise dealer.
|
|
|
|
|
454 478 00 12
Fuel Tank Module Seal 2007-2018
Seals tank access port for fuel pump and/or sending unit (under threaded collar)
|
|
|
|
|
000 905 08 00
Fuel Temperature Sensor 2014-2016 2.1L 4 CYLThis is the smaller threaded senor, located on the injection pump
|
|
|
|
|
642 070 21 95
Left Fuel Distribution Rail 2007-2009 3.0L V6Left or driver's side rail
The fuel control valve with the 90 degree connection is only available with the fuel rail and is included.
|
|
|
|
|
642 070 27 95
Left Fuel Distribution Rail 2010 & LATER 3.0L V6Driver's side rail. Includes Fuel Control Valve on end of rail.
The fuel control valve (642 070 02 46) with the 90 degree connection is only available with the fuel rail.
|
|
|
|
|
642 070 25 95
Right Fuel Distribution Rail 2007-2009 3.0L V6Right or Passenger's side rail
Includes the straight electrical fuel pressure sensor at back end of the rail. |
|
|
|
|
642 070 30 95
Right Fuel Distribution Rail 2010 & LATER 3.0L V6Right side or Passenger's side
|
|
|
|
|
642 090 03 44
Throttle Body Flange 3.0L V6 Diesel 2007-2018Black plastic flange that attaches to the throttle body.
|
|
|
|
|
907 300 02 00
Throttle Pedal Actuator-METRIS & SPRINTER 2007 & LATERComplete assembly, with pedal.
|
|
|