|
|
|
642 092 01 01X10
2004-2009 Sprinter-HENGST H278WK Diesel Fuel Filter-10 PACK ***2 to 3-Day Shipping Included**This is a pack of ten diesel fuel filters
Two o-ring seals are included with each filter
Not for 2002-2003 models, and not for 2010 and later engines.
2 to 3-Day Shipping to any US Zip Code included!
ONLY VALID FOR SHIPPING TO A US ZIP CODE
|
|
|
|
|
642 078 00 01
2007-2009 Sprinter 3.0 V6 Diesel Fuel Hose Kit ***FREE USA SHIPPING***REQUIRES SIX 13MM AND SIX 15MM HOSE CLAMPS, SHOWN BELOW.
All the six small fuel hoses in and around the engine compartment, labeled A thru F on our site. All are Genuine Mercedes parts.
The fuel return hose assembly (H) and drain/purge line (G) are NOT included. You can see these two hoses below, along with the special hose clamps for fuel hoses.
|
|
|
|
|
33336
Cooling System Oil CleanerCleans the entire cooling system and removes oily deposits caused by blown cylinder head gaskets or internally leaking oil coolers.
|
|
|
|
|
642 092 03 01
Diesel Fuel Filter - SHORT VERSION 2010-2012 3.0L V6 Diesel (3-pin Moisture Sensor)
Includes filter, and 4 O-ring seals.
Not for 2004-2009 models, which have a much smaller moisture sensor hole in the center.
If
you are planning on removing and replacing the original Clic style
fuel hose clamps on top of the filter, you will need one 13 mm clamp and
one 15mm clamp.
|
|
|
|
|
651 090 29 52-HENGST
Diesel Fuel Filter- V6 & 4 Cylinder Diesel Engines - Hengst
Fuel filter for 2010 and later 3.0L V6 Diesels and all 2014-2016 2.1L 4 CYL Diesels.
This fuel filter includes a fixed, non-removable, five-pin moisture sensor. The attached water purge hose, unlike the original V6 factory style, is less costly than the original style filter without the hose and is completely interchangeable with the original V6 style filter. It also allows a quick method of draining accumulated moisture from the filter.
Some 2010-2012 V6 diesels use a
different fuel filter, a physical inspection may be required, as there
is no way to determine this fitment from the VIN. You can see the other
version fuel filter below, which has a large hole in the center for a
removable 3-pin water/moisture sensor.
|
|
|
|
|
651 090 29 52-MANN
Diesel Fuel Filter- V6 & 4 Cylinder Diesel Engines - MANN
Fuel filter for 2010 and later 3.0L V6 Diesels and all 2014-2016 2.1L 4 CYL Diesels.
This fuel filter includes a fixed, non-removable, five-pin moisture sensor. The attached water purge hose, unlike the original V6 factory style, is less costly than the original style filter without the hose and is completely interchangeable with the original V6 style filter. It also allows a quick method of draining accumulated moisture from the filter.
|
|
|
|
|
642 092 01 01
Diesel Fuel Filter-HENGST H278WK (OEM) 2004-2009Two O-ring seals are included with the filter, which are to be used on the moisture sensor in the center of the filter element.
These are for 2004 to 2009 model years only - Not for 2002-2003 or any Sprinter engines 2010 and later.
If you are planning on removing and replacing the original "Clic" style fuel hose clamps on top of the filter, you will need 1 x 13 mm clamp
and 1 x 15mm clamp, see below.
|
|
|
|
|
642 092 04 01
Diesel Fuel Filter-MAHLE KL490/1D LONG VERSION 2010-2012 3.0L V6 Diesel (3-pin Moisture Sensor)Includes filter, & 4 o-ring seals.
Not for 2004-2009 models, which have a much smaller moisture sensor hole in the center.
THIS IS NOT A FILTER THAT WAS SUPPLIED AT THE ASSEMBLY PLANT. IT IS A LESS COSTLY OPTION FOR THOSE WANTING TO DO A CONVERSION.
If
you are planning on removing and replacing the original Clic style
fuel hose clamps on top of the filter, you will need one 13 mm clamp and
one 15mm clamp.
|
|
|
|
|
LM2005
Diesel Purge 2002 & LATER
Label description:
Diesel Purge contains a mixture of agents with powerful cleaning properties. The special additives guarantee corrosion protection and increase ignition performance (Cetane number).
|
|
|
|
|
33151
DPF Catalyst Cleaner
Catalyst/DPF Cleaner
- Dissolves and removes contamination in the diesel particulate filter and catalyst.
- Cleaning without dismantling
- Evaporates residue-free
- Dispense product directly onto DPF core using supplied straw through temperature sensor port on DPF.
|
|
|
|
|
808
DPF Filter Purge
Designed to reduce the ignition temperature of soot collected in the DPF, improving fuel economy and maintaining a clean filter.
|
|
|
|
|
651 200 60 00
Fuel Filter Bracket/Water Outlet Flange 2014-2016 2.1L 4 CYLThis unit holds the fuel filter on the 2.1L 4 CYL engines, although it is technically part of the cooling system.
This part has been updated several times by Mercedes, due to leakage problems. This is the newest version.
|
|
|
|
|
027 997 86 48
Fuel Filter O Ring 2002-2009 SprinterThis O ring is used on the fuel filter moisture sensor. One or two are required, depending upon the model year.
|
|
|
|
|
642 070 12 38
Fuel Filter Purge Hose (3 Pin Moisture Sensor) 3.0L V6 2010-2012
This hose connects to the moisture sensor on top of fuel filter and is the only one furnished with a metal bracket. Bleed screw is at the opposite end.
NOTE: This hose is used on those models which have the type of fuel filter with the removable 3-pin moisture sensor from 2010 to 2012
DO NOT ORDER THIS IF YOU HAVE A FUEL FILTER WITH THE NON-REMOVABLE 5-PIN MOISTURE SENSOR.
See the other version of this hose below
|
|
|
|
|
642 070 24 38
Fuel Filter Purge Hose (5 Pin Moisture Sensor) 3.0L V6 2010-2018
Hose to top of fuel filter. Snaps onto the small nipple at the top on the side. This hose has a bleed screw on the end for purging accumulated water at the bottom of the fuel filter.
NOTE: This hose is only used in conjunction with the new BlueTec engine fuel filters with the non-removable 5-pin moisture sensor.
See the other version of this hose below.
|
|
|
|
|
642 070 00 38
Fuel Filter Purge Hose 3.0L V6 2007-2009
This hose connects to the moisture sensor.on top of fuel filter. Bleed screw is at the opposite end.
DO NOT ORDER THIS HOSE IF YOU HAVE A 2010 OR LATER MODEL WITH A BLUETEC ENGINE.
THERE ARE TWO DIFFERENT FUEL FILTER PURGE HOSES FOR 2010 AND BOTH ARE SHOWN BELOW
|
|
|
|
|
642 090 64 52
Fuel Filter V6 Diesel 2010+
Original style fuel filter for 2010 and newer 3.0L V6 Diesels that came with the non removable 5 pin sensor.
This filter does not include the purge hose that often breaks. A better option would be this filter HERE.
|
|
|
|
|
642 070 04 81
Fuel Hose A 3.0 V6 2007-2009Hose uses 2 x 13 mm clamps
|
|
|
|
|
642 070 57 81
Fuel Hose A 3.0L V6 2010 & LATER
REQUIRES TWO 13MM CLAMPS.
Fuel filter to high pressure injection pump
|
|
|
|
|
642 070 05 81
Fuel Hose B 3.0 V6 2007-2009Hose from output side of fuel filter to high pressure injection pump
Hose uses 13mm clamps
|
|
|
|
|
642 070 36 81
Fuel Hose B 3.0L V6 2010 & LATER
Only for 3.0L V6 Diesel
REQUIRES TWO 13MM CLAMPS. |
|
|
|
|
642 078 19 81
Fuel Hose C 3.0L V6 2007-2009One of two hoses that connect the fuel pipe sections together
Hose use 15 mm clamps
|
|
|
|
|
642 078 45 81
Fuel Hose C 3.0L V6 2010 & LATER
Only for 3.0L V6 Diesel
Fuel filter to separator
REQUIRES TWO 15MM CLAMPS.
|
|
|
|
|
642 078 13 81
Fuel Hose D 3.0L V6 2010 & LATER
Only for 3.0L V6 Diesel BlueTec
REQUIRES TWO 15MM CLAMPS.
|
|
|
|
|
642 078 21 81
Fuel Hose D 3.0L V6 2007-2009Short, straight 50mm (2 inch) section
13mm clamp on each end
|
|
|
|
|
642 078 32 81
Fuel Hose E 3.0L V6 2010 & LATER
Only for 3.0L V6 Diesel BlueTec
REQUIRES TWO 15MM CLAMPS.
PART # ON HOSE IS 642 078 32 81
|
|
|
|
|
642 078 23 81
Fuel Hose E 3.0L V6 2007-2009Feed hose from metal pipe to input side of fuel filter
Hose uses 2 x 15 mm clamps
|
|
|
|
|
642 078 25 81
Fuel Hose F 3.0L V6 2007-2009Hose uses 2 x 15 mm clamps
|
|
|
|
|
21013
Fuel Injection Hose Clamp 13 mm 2002 & LATER
Clamping Range 12.5 - 14mm
These are special fuel hose clamps with rolled edges and no open serrations so the clamp will not cut into the hose.
If you are replacing all of the original Mercedes factory "Clic" style clamps on a ......
2002-2003 Sprinter...................... Order 4 x 13mm clamps
2004-2006 Sprinter...................... Order 9 x 13mm clamps & 1 x 15mm clamp
2007-2009 Sprinter...................... Order 6 x 13mm clamps & 6 x 15mm clamps
|
|
|
|
|
21015
Fuel Injection Hose Clamp 15mm 2002 & LATERClamping Range 13.5 - 15.5mm
These are special fuel hose clamps with rolled edges and no open serrations so the clamp will not cut into the hose.
If you are replacing all of the original Mercedes factory "Clic" style clamps on a ......
2002-2003 Sprinter........... Order 4 x 13mm clamps
2004-2006 Sprinter........... Order 9 x 13mm clamps & 1 x 15mm clamp
2007-2009 Sprinter........... Order 6 x 13mm clamps & 6 x 15mm clamps
|
|
|
|
|
21017
Fuel Injection Hose Clamp 17mm 2002 & LATERClamping Range 16-18 mm
These are special fuel hose clamps with rolled edges and no open serrations so, the clamp will not cut into the hose
If you are replacing replacing all of the original Mercedes factory "Clic" style clamps on a ......
2002-2003 Sprinter........................order 4 x 13mm clamps
2004-2006 Sprinter........................order 9 x 13mm clamps & 1 x 15mm clamp
2007-2009 Sprinter........................order 6 x 13mm clamps & 6 x 15mm clamps
|
|
|
|
|
601 997 03 45
Fuel Line Seal Ring 2002-2003 & 2007-2009
O-ring used at both ends of the white plastic fuel lines on the OM612 5 CYL engine
Also used on 2007-2009 3.0 V6 on end of fuel purge hose where it enters the fuel filter.
Do not order these seal rings if you are ordering new hoses, as the hoses are furnished with the seals already in place.
|
|
|
|
|
000 997 26 63
Fuel Purge Hose Coupling/Screw 2007 & LATERThreads into the top of fuel filter moisture sensor for 2007 and later 3.0L V6 engines
Used for attaching the fuel purge hose to the moisture sensor.
|
|
|
|
|
001 991 58 70
Fuel Return Line Retainer Clip 2002 & LATERLocated at top of each injector
|
|
|
|
|
901 470 04 05
Fuel Tank Cap 2002-2018Black plastic cap with seal included. |
|
|
|
|
901 476 00 26
Fuel Tank Filler Coupler 2002-2006Connects the filler tube to the fuel tank.
|
|
|
|
|
901 470 13 20
Fuel Tank Filler Neck 2002-2006Approximately 500mm long (20 inches) |
|
|
|
|
LM2000
Particulate Filter Protector 2007+Protects the diesel particulate filter. Aids the regeneration of DPF
systems. Ensures optimal fuel combustion. Reduces the build-up of
particulates. Especially suited for vehicles used for city driving and
those that drive short distances. Add to diesel fuel immediately before
filling up.
THIS PRODUCT MAY ONLY BE SHIPPED BY GROUND TRANSPORTATION (FEDEX GROUND OR UPS GROUND)
NO MAIL, NOR AIR SHIPPING IS PERMITTED BY FEDERAL LAW.
|
|
|
|
|
LM2002
Super Diesel Additive 2002 & LATER
Description from the Product Label:
Cleans thoroughly and prevents deposits from forming in fuel systems and combustion chambers. Keeps the injectors clean and guarantees improved engine combustion leading to a lower specific fuel consumption and the maximum engine performance.
Prevents seizing and the injector needles from gumming up. Increases the lubrication action of diesel fuels low in sulfur (low sulfur diesel in accordance with DIN EN 590) and protects distributor injector pumps from wear. Increases the Cetane number of diesel fuel, leading to a smooth and gentle combustion process. Contains antioxidant and prevents corrosion. Compatible with all modern diesel oxidation catalytic converters.
THIS PRODUCT MAY ONLY BE SHIPPED BY GROUND TRANSPORTATION (FEDEX GROUND OR UPS GROUND). NO MAIL, NOR AIR SHIPPING IS PERMITTED BY FEDERAL LAW. |
|
|
|
|
11050
Type A Hose Clamp 38-50mmClamping Range 38-50mm
Rolled clamp edge and smooth inside band will not cut into the hose. High quality made in Sweden.
|
|
|
|
|
11056
Type B Hose Clamp 44-56mmClamping Range 44-56mm
Rolled clamp edge and smooth inside band will not cut into the hose.
High quality made in Sweden.
|
|
|
|
|
11065
Type C Hose Clamp 50-65mmClamping Range is 50-65mm.
Rolled clamp edge and smooth inside band will not cut into the hose.
High quality Made in Sweden.
|
|
|
|
|
11044
Type D Hose Clamp 32-44mmClamping Range 32-44mm
Rolled clamp edge and smooth inside band will not cut into the hose. High quality made in Sweden.
|
|
|
|
|
611 078 00 71
Water/Fuel Bleed Screw 2002-2018Located in side of fuel filter, at bottom of canister on 2002-2003 models.
Located on top of fuel filter moisture sensor for 2004-2006 models. (2007-2009 V6 diesels use a different coupling on top, see below)
Located on fuel hose and fuel filter for 2007 and later models
Used for bleeding any water and /or air from fuel filter and fuel system.
|
|
|
